Hubcaps anybody?

[Fraser]

DSCF5659 (2).JPG

DSCF5661 (2).JPG

DSCF5662 (2).JPG

I have this one '69 Explorer disc. It's not perfect, but kind of rare, so asking $50.00. plus actual shipping. I think it's repairable, as damage is accessible from behind, or use it with the "patina" #16 on the hubcap page of this site.
I also have 8 crappy re pops of style 2, not stainless but chromed steel, and they have rusted. Only use would be to paint over them for a retro-custom look. four for $10 plus freight. Can send pics to your E-Mail, but don't expect much.
I have some others, but they are snowed in until April, at least. I will know better at that time, but I think I have 2 '60s dog dish #4, 2 "67 car/truck type#6, 4 '80s 15" #13, and some '70s dog dishes #5 but some are GM. Lets say $25 each for these. Pre-bump era, I have some late '50s, and some early '60s painted "innie" caps.
Also, Looking for '62 Mercury truck innies (1/2 ton)

On another note, I have a '67 radio delete plate. I don't know, make an offer.

[DisneysPatB]

Any like this? http://www.flickr.com/photos/9426598@N0 ... 689hNF5k9W

[Fraser]

Painted 3/4 ton? I think I have 2 painted ones, will check.

[Fraser]

From '73 MPC.

DSCF5670 (2).JPG

DSCF5672 (2).JPG

Pat, I found this, Can't seem to put it in the PM I sent.

DSCF5668 (2).JPG

[DisneysPatB]

They are 12" and not the smaller 9" correct?

[Big specht]

I’m looking for some of those steel hub caps too

[Fraser]

I’m looking for some of those steel hub caps too

I have at least 1 more, but it's in worse shape and stored at a very snow covered farm until spring, I can PM you then.

[Big specht]

Those caps are for the wheels that have the tits that on the inside ? You have a pic of the back side ?

[Fraser]

The caps have no tits, I think you mean the rim bumps. I have seen the caps referred to as outies, Innies are not for sale at this time

DSCF5679 (2).JPG

[Big specht]

Yea I’m looking for a set of innie caps. I would post a pic but it keeps saying the pic is to big

[Fraser]

I know which ones you are after, my '67 has innies, they only fit early split rims. I have not decided what direction I'm going with that, so not selling them until I do.
I have to change out that stupid-low 456 rear, and may just convert to 1/2 ton running gear. I know gas was cheap in '67 but come on, 456:1????

As for pictures, I have to take a picture from way back and crop it, sometimes I still have to resize the pixel count even farther.

[Big specht]

E27403AD-472E-4DB4-8D94-2134B8821E6C.jpeg

I got it not as good as I wanted but you will know what I meant . And these are for some factory wide wheels I have.

[Fraser]

Yeah, that's what my '67 has. I think '66 still used a "bottle cap" style, and the outies shown above, have a C8UZ part #.
If you expand the MPC page I posted earlier, about 5 lines up is a part # C7TZ 1130 A, which, I think, is what you want, and still in use in that '73 manual.

[Fraser]

Deleted

[Fraser]

Now that the snow is gone, I've got pictures of some others, I have multiples of some.

DSCF7018 (2).JPG

DSCF7020 (2).JPG

That Mercury cap may just be a wall hanger. I have four of the '77ish black plastic caps for the white rally rims, but the picture won't take here.
Prices starting at $25, which includes packaging and handling. Actual shipping will be additional, at cost.